Govee Lyra RGBICWW Corner Floor Lamp Setup Guide

Govee Lyra RGBICWW Corner Floor Lamp

  • Tools required:
    • Soft cloth for unpacking and cleaning
    • Tape measure to check placement and cable length
    • Cable ties or adhesive cable clips for cable management
    • Small screwdriver (Philips or flat) — only if the unit includes screws for a base or cover
  • Applications:
    • not specified

• Capabilities: RGBIC (individually addressable colour segments); dedicated warm-white LEDs for natural-toned illumination; freestanding corner floor design for ambient and accent lighting.
• Connectivity: not specified — consult the supplied quick start guide or product manual for wireless or app-based control information if included with your unit.
• Compatibility: not specified.

• Step 1 — Unpack and inspect: Remove the lamp from its packaging and retain the box and protective material until setup is complete. Check for visible damage to the housing, LED strips, cable and plug. If anything is damaged, do not use the lamp and contact the seller.
• Step 2 — Identify parts and any assembly requirement: Verify whether the lamp is supplied assembled or in sections (for example a base, column segments or a top cap). If the unit includes screws or fasteners, use the small screwdriver to secure parts by hand until snug; do not overtighten. Follow any paper instructions that accompany the lamp.
• Step 3 — Choose placement: The Lyra is designed to sit in a corner. Measure the distance from the corner to the nearest power outlet so the cable will reach without stretching. Ensure the lamp stands on a stable, level floor and will not obstruct walkways.
• Step 4 — Route and secure the cable: Run the power cable along skirting boards and secure with adhesive cable clips or cable ties; leave a small service loop rather than pulling the cable taut. Keep the cable away from heat sources and sharp edges. Ensure the plug and any inline switch are accessible.
• Step 5 — Electrical safety check before powering: Inspect the plug and cable for damage, ensure the outlet is switched off if applicable, and confirm the outlet is suitable for the plug provided. If the product requires hard-wiring to household mains (not typical for plug-in floor lamps), that work must be performed by a trained electrician.
• Step 6 — Powering on: Insert the plug into the outlet and switch the outlet on (if applicable). Use any physical switch located on the lamp or the inline switch to turn the lamp on. If the lamp includes remote or app control, consult the manual for pairing and control steps—connectivity method is not specified in the product details.
• Step 7 — Using colour and warm-white functions: The lamp contains RGBIC segments for multi-colour effects and separate warm-white LEDs for natural-toned illumination. Control and mode selection depend on the unit's provided controls (physical buttons, remote or app). If an app or remote is supplied, use it to select RGBIC effects, adjust colours for individual segments (where supported), and adjust warm-white brightness/colour temperature. If controls are not present or not obvious, refer to the printed manual included with the product.
• Step 8 — Basic troubleshooting:
   – If the lamp does not light, check the outlet with another device and confirm the outlet switch (if present) is on.
   – Check that any inline switches or connectors are fully engaged and that any supplied batteries for a remote control are fitted correctly.
   – If app pairing is required and fails, ensure Bluetooth/Wi‑Fi on the controlling device is enabled (only if your unit supports wireless control — connectivity not specified) and follow the manufacturer instructions.
• Step 9 — Ongoing use and maintenance: Turn the lamp off and unplug before cleaning. Wipe with a soft, dry cloth; do not use solvents or abrasive cleaners. Keep the lamp away from water and high humidity. Do not attempt internal repairs; if the lamp fails electrically, contact a qualified technician or the point of purchase.
• Safety note: Do not assume the lamp is low-voltage. If installation or modifications require direct wiring to household mains (hard-wiring) or any work inside the lamp, this must be carried out by a trained electrician. Avoid exposing the lamp to moisture, and do not cover the unit while lit.

Product UID: 10434225799495