Govee Glide HEXA Light Panels (10 Pack) Setup Guide

Govee Glide HEXA Light Panels (10 Pack)

  • Tools required:
    • Soft cloth and isopropyl wipe (or mild cleaner) for surface preparation
    • Tape measure and pencil for layout marking
    • Spirit level or laser level for alignment
    • Scissors or utility knife (for trimming adhesive backing, if applicable)
    • Screwdriver or drill and appropriate screws / wall anchors (only if you choose mechanical fixing)
    • Small step ladder (if installing above shoulder height)
  • Applications:
    • not specified

Capabilities and connectivity: modular hexagonal LED panels; customisable arrangement and layout; suitable for ambient and accent lighting; intended for multi-panel installations. Connectivity: not specified. The panels are intended for indoor decorative use. Follow the steps below for a safe, neat installation.

  • Step 1 — Inspect the kit and read the manufacturer instructions
    Unpack the panels and any included accessories (connectors, control module, power supply, adhesive strips, screws). Confirm you have ten panels and any linking cables or connectors supplied by the manufacturer. Keep the manufacturer manual to hand and follow any specific instructions it contains; this guide covers general, non-electrical assembly and mounting steps only.
  • Step 2 — Plan the layout
    Lay the ten panels on the floor and experiment with shapes until you have the desired arrangement. Measure the wall area and mark the intended top, bottom and outer edges lightly with a pencil. Note where the power/control module will sit so cables reach an existing socket without tension.
  • Step 3 — Prepare the mounting surface
    Clean the wall where each panel will be mounted using a soft cloth and an appropriate cleaner or isopropyl wipe. Allow the surface to dry completely. Avoid mounting on freshly painted surfaces or wallpaper that may peel; test an adhesive strip in an inconspicuous area if unsure.
  • Step 4 — Test-assemble panels before fixing
    Connect panels together on the floor using the supplied connectors or link cables to verify fit and orientation. If a control module or power lead is present, connect it and perform a power-on test to confirm panels light correctly before mounting.
  • Step 5 — Choose mounting method
    Use the manufacturer-supplied adhesive strips or mounting tape for damage-minimising installation on smooth, clean walls. If you prefer a more permanent fix, use screws and wall anchors appropriate for your wall type. Do not mix mounting methods on adjacent panels as this may affect alignment.
  • Step 6 — Mount the first panel and align
    Start with the panel at the centre or highest point of your planned layout. Apply adhesive strips to the panel backing as instructed by the manufacturer, or prepare screw positions and pilot holes. Use a level to ensure the first panel is straight; subsequent panels should align to this reference.
  • Step 7 — Complete assembly and connection
    Attach each subsequent panel, connecting edge-to-edge with the supplied connectors or cables. Keep connectors fully seated; loose connections can cause lighting faults. Route cables neatly towards the control module, avoiding sharp bends. If the kit includes a controller box, mount it close to a power socket while leaving enough slack for cable access.
  • Step 8 — Final checks and power-up
    Once all panels are mounted and connected, perform a final check of all mechanical fixings and cable routing. If a power supply or adapter is included with the kit, plug it into the control module and then into the mains. If the product requires specific control hardware or an app, follow the manufacturer instructions to pair or configure—the presence and type of app control is not specified in the product information.
  • Step 9 — Adjust and maintain
    Adjust panel positions slightly if needed while adhesive is still repositionable (if using repositionable strips). Avoid exposing panels to moisture or direct heat. Clean panels with a soft dry cloth; do not use abrasive cleaners or submerge panels.
  • Important safety notes
    These panels are for indoor decorative use only. Do not install near water, outdoors or where they may be exposed to high temperatures. Do not cut, puncture or attempt to open LED modules or power supplies. If the kit requires connection to fixed mains wiring or hard-wiring to a 240 V supply, that work should be performed by a trained electrician in accordance with local regulations. If in doubt about electrical connections or missing items, consult the manufacturer documentation before proceeding.

If any part of the kit is missing or appears damaged, stop and contact the supplier; do not attempt to operate damaged electrical components. For function-specific setup (app pairing, voice assistant linking, advanced scenes), refer to the official manufacturer guide supplied with your product, as control method and connectivity are not specified here.