Aqara LED Strip T1 Extension (1m) Setup Guide

Aqara LED Strip T1 Extension (1m)

  • Tools required:
    • Tape measure or ruler (to plan run length)
    • Clean, lint-free cloth and isopropyl wipe (for surface preparation)
    • Adhesive clips or cable clips (for neat routing)
    • Small flat work surface and good light
  • Applications:
    • Aqara Home app (the product description refers to configuration in the Aqara app)
    • Zigbee or Matter controller/gateway where used — tags indicate Zigbee and Matter compatibility, but specific hub requirements are not specified

Setup steps

  • Confirm compatibility: this extension is designed specifically for use with the Aqara LED Strip T1 base kit. It is an add-on metre; it will not function alone without the T1 base kit.
  • Power off the LED Strip T1 base kit before you start working on the physical connection. Disconnect the base kit from power to avoid accidental operation while connecting parts.
  • Plan the run: measure the total strip length you need including the base kit and any extensions. The product page states you can add one or more extensions; the maximum supported run length or power handling is not specified here — consult your T1 base kit documentation for maximum length and power-supply limits.
  • Prepare surfaces: clean the mounting surface with the cloth/isopropyl wipe and allow to dry. This ensures adhesive on the strip and any clips will stick correctly.
  • Unpack and inspect: remove the extension from its packaging and check the plug-in connector and strip for any visible damage. The product description states a simple plug-in connection with no soldering required for standard layouts.
  • Join the extension to the existing T1 strip:
    • Align the extension connector with the matching end of the T1 strip. Ensure pins/contacts align—do not force at an angle.
    • Push the connector together until it seats firmly. For some layouts you may hear or feel a small click; ensure the joint is secure and the strip lies flat.
  • Route and fix the strip:
    • Use the strip's adhesive backing and/or adhesive clips to fix the strip into place. Press evenly along the adhesive sections so the strip is fully supported.
    • Avoid sharp bends and keep the strip within the recommended bend radius of the base kit (refer to the T1 kit documentation for bend guidance).
  • Power on and verify physical connection: reconnect power to the base kit and confirm the LED strip illuminates. If the extension or segment does not light, power off and recheck the connector seating and alignment.
  • Configure in the Aqara app:
    • Open the Aqara Home app on your phone and select your LED Strip T1 device (the description notes the extension keeps full RGBIC and tunable white support when correctly configured in the Aqara app).
    • If the app prompts for strip length, segment setup or calibration, follow the on-screen instructions to include the added metre so effects and segment mapping remain correct.
    • Update the device firmware if prompted by the app before finalising configuration.
  • Check colour and effect behaviour: after configuration, test RGBIC effects and tunable white modes. The product description states full RGBIC and tunable white support is retained when correctly configured in the Aqara app.
  • Multiple extensions and power considerations: if you plan to add several extensions, verify the T1 base kit power supply can support the total length. Maximum run limits and power-handling details are not specified in this extension listing — consult the LED Strip T1 base kit documentation for limits and recommended power arrangements.

Troubleshooting

  • No light on extension: power off, disconnect and re-seat the plug-in connector; check for debris on contacts and ensure the connector is not reversed or forced.
  • Colour or effect mismatches: open the Aqara app, check device settings for strip length/segment mapping and update firmware if available. If the app shows the strip as a single unit, ensure you saved any length/segment changes.
  • Adhesive not sticking: clean the surface again, allow to dry fully and use adhesive clips for mechanical support where necessary.
  • Network or integration issues: if using a Zigbee or Matter controller, ensure the controller supports Aqara LED Strip T1 and that the base kit is connected to that controller. Specific hub compatibility and setup steps are not specified here.

Notes: This extension is a plug-in accessory for the Aqara LED Strip T1 base kit. It is 1 metre in length as described. Maximum run length, power-supply ratings and certain hub compatibility details are not specified in this product description—refer to the T1 base kit documentation or Aqara support for those technical limits.