Aqara LED Strip T1 (2m) Setup Guide

Aqara LED Strip T1 (2m)

  • Tools required:
    • Measuring tape or ruler
    • Sharp scissors or strip cutter (cut only at marked cut points)
    • Isopropyl alcohol wipe or a lint-free cloth and cleaner
    • Small flat-head screwdriver or connector tool (if using clip connectors)
    • Optional: extension connectors or joiner cables if extending beyond 2 m
    • Power supply and hub/controller compatible with the strip: not specified in product text (see "Applications" below)
  • Applications:
    • Aqara Home app or your Aqara hub controller app (for Zigbee/Matter integration) — exact app requirement not specified in product text
    • Compatible Zigbee or Wi‑Fi hub that supports Aqara devices and Matter (where supported by your hub)
    • Optional: third‑party controller or LED decoder only if explicitly supported by your chosen hub (support not specified here)

Capabilities and connectivity (as specified): Individually addressable segments with gradient effects, tunable white plus full colour range, adhesive backing, cuttable and extendable up to 10 m, and support for Zigbee, Wi‑Fi and Matter via a hub.

Step-by-step setup and installation

  • Plan the run: measure the area where you will install the strip. Confirm the total length will not exceed the stated extendable limit of 10 m. Keep the controller/hub and power supply location in mind so cable reach is sufficient.
  • Check the strip before installation: uncoil the 2 m strip on a flat surface and inspect for any visible damage. Identify the marked cut points on the copper pads; only cut at those marks.
  • Prepare the surface: clean the mounting surface thoroughly with isopropyl alcohol or a suitable cleaner and allow it to dry. The adhesive backing adheres best to smooth, dry surfaces.
  • Cutting and joining: if you need to shorten the strip, cut only at the printed cut lines. If you intend to extend the strip, use only compatible extension joiners or connectors rated for this product; follow connector manufacturer instructions. The document does not specify connector types or wiring details.
  • Power supply and controller: the product description does not specify the required power supply voltage or whether a power adapter is included. Use a compatible Aqara power adapter or the power output provided by your Aqara controller/hub as required. Do not attempt to connect to mains wiring unless the product or your hub explicitly provides a suitable interface and you are qualified to do so.
  • Mounting the strip: peel back a small section of the adhesive backing, align the strip and press firmly along the length. Apply even pressure to secure. For corners or uneven surfaces, use gentle radii or appropriate mounting clips; avoid sharp bends that could damage the LEDs.
  • Make connections: attach the strip to the controller or connector cable following the polarity and pin layout provided by the controller or connector. If the controller requires a separate cable, connect that cable to the strip’s connector. If using multiple strips or extensions, ensure each join is secure and insulated as required. The product description does not specify connector pinouts—refer to your controller or connector documentation.
  • Place and power the controller/hub: position the controller or hub in a ventilated area. Connect the controller to the power supply. Connect the controller to your network/hub according to the controller's instructions. If the product requires a hub for Zigbee or Matter, ensure that hub is powered and online before attempting device pairing.
  • Pairing the strip with your hub/app: open the Aqara Home app or your hub’s app and follow the standard device add/pair procedure for Aqara LED devices. Typical steps: put the hub/controller into pairing mode, power on the strip/controller, wait for the app to discover the device, then confirm pairing. If the strip supports direct Wi‑Fi setup, follow the app prompts. Exact pairing steps depend on your hub and app; the product text confirms support for Zigbee, Wi‑Fi and Matter via a hub but does not give exact pairing instructions.
  • Verify and configure: once paired, verify the strip responds to on/off, white temperature and colour commands. Because the strip is addressable, configure any segment lengths or LED count in the app if prompted to ensure gradients and effects work correctly. Save scenes, schedules or automations in your app as required.
  • Final checks: run through common effects and white tuning to confirm correct behaviour across the full installed length. Secure any loose cables and ensure connectors are protected from moisture and mechanical strain.
  • Troubleshooting tips:
    • No power: re-check power connections and the controller’s power LED. Verify the power supply is the one recommended by your controller or Aqara documentation (not specified in the product text).
    • No discovery in app: ensure the hub/controller is in pairing mode and on the same network if using Wi‑Fi; try power-cycling the controller and strip. Confirm the hub firmware and app are up to date.
    • Uneven colours or missing segments: check connector orientations and that joins are secure; verify you have not exceeded the maximum extendable length.

Notes: Do not assume mains wiring details or power supply specifications not stated here. The product text does not specify supply voltage, connector pinouts or whether a power adapter is included. If your installation requires work on fixed mains (230 V) wiring, that work should be carried out by a trained electrician. For any unclear electrical or compatibility questions, consult Aqara support or your hub/controller documentation.